No 3D Target Ring with Custom UI???
<img src="http://www.eqinterface.com/images/sections/eqpatch.gif" align="right">Aario was kind enough to email the following solution for the problem of no 3D target ring while using Custom UIs
Quote:
All test seem to point that this is a good fix for the problem. This is most likely a glitch with the UI since all other files are pulled from the default folder. I would expect SOE to fix this soon. Thank Aario! - Kudane |
Okay, straight from SOE's Tech Help forum, this thread posted by Roger Sewell:
Quote:
|
Thanks to Aario
Thanks to Aario I have the target Indicator working in my AYA UI.
For those that use aya650r3 just a bit of info. I copied the Default Options window into the AYA UI and that made it compatable XML. It maintained the same general apperance and gives me the "Font" change and "Tell" options. It will work until the Author has a chance to up date the UI. |
You need this..
make sure to have
UseTNl = TRUE in your eqclient.ini as well, or you don't see anything. |
Re: You need this..
Quote:
Aha! I didn't have that. I copied and pasted that into Notepad, will give it a try. To confirm, that's TN1 as in Thomas Newton (One), and not TNI as in Thomas Newton Indigo? |
Re: You need this..
Quote:
I have no line even remotely similar to this in my eqclient.ini.. Any clues as to where in the file it is supposed to be? |
just add the line in there.
TNL as in thomas newton lunchbox |
I'm still very confused. What file do I replace with what file, or what do I change in which ini file?
Thanks for the help. |
I've tried all these things with no luck.
I'm using a NVidia GeForce4 MX 440 video card. |
You may wish to read this post by Roger Sewell of SOE.
|
already read that. no workie. :mad:
|
Quote:
Should explain why it doesnt work and why it may never work for you. ;) |
The earlier post in this thread point you in the right direction, but are innacurate.
- The line belongs in the "defaults" section of your eqclient.ini file. It is *not* there by default for many people. - The line above will not work if copy and pasted. The correct line is UseTNL=TRUE, not UseTN1=TRUE. (Tommy Newton Lemon) - The "true" toggle did not work for me; I had to use the numeric toggle set to 1 (one). So, the line that actually worked for me was: UseTNL=1 Copied and pasted right into the DEFAULTS section of eqclient.ini. I rebooted EQ and it's worked like a charm since, even with all spells and effects off and whatnot. |
Re: You need this..
Quote:
See Roger's comment about using this command.. only those with the ATI 9600 series should add this, at this time.. and TnL as in Texture n Lighting goodluck! |
possible fix
I had a prob with the target ring not working on both my desktop and laptop. Cards i have are GF 4 TI 4600 and a GF 4 420 Go. Before the patch i was using a custom UI. When i swicthed to default mode I couldn't get the rings either.
Just deleting the custom UI folders didn't fix it , then i tried the unifiles folder... no cure. Then I tried this ..... works great now. I deleted my Unifiles folder and all files UI_(Char Name) and all files with (Char Name)_eci. Run the patcher using the complete file check. I logged in and had the rings working , so then I downloaded the custom UI and a Custom target ring again. Made a folder in the unifiles one to unzip both the UI and target ring into. Problem was cured. Surprised my laptop even displayed the rings nicely. |
All times are GMT -5. The time now is 11:43 AM. |
vBulletin Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.